ReferenceDesignLibrary

Designs (793)

793 Results - Page 1/80 |< < 1 2 3 4 5 > >|

STEVAL-ISA055V1: 1.2V @ 700mA, 2.5 ~ 5.5V in

Manufacturer: STMicroelectronics

This demonstration board is based on the ST1S12 family of synchronous step-down DC-DC converters optimized for powering low-voltage digital cores in HDD (hard disk drive) applications and is generally used to replace high-current linear solutions when power dissipation may cause high heating of the application environment.

View Design

STEVAL-ISA055V2: 3.3V @ 700mA, 5V in

Manufacturer: STMicroelectronics

This demonstration board is based on the ST1S12 family of synchronous step-down DC-DC converters optimized for powering low-voltage digital cores in HDD (hard disk drive) applications and is generally used to replace high-current linear solutions when power dissipation may cause high heating of the application environment.

View Design

STEVAL-ISA050V1: DDR2/3 Supply

Manufacturer: STMicroelectronics

The PM6641 demonstration board is a monolithic voltage regulator (VR) module with internal power MOSFETs, specifically designed to supply DDR2/3 memory and chipset in ultramobile PC and real estate constrained portable systems.

View Design

EVL6591-90WADP: 90W, 12V @ 7.5A, 88 ~ 264Vin

Manufacturer: STMicroelectronics

This document describes the characteristics and performance of a 90 W wide range input AC-DC adapter based on asymmetrical half-bridge topology (AHB).

View Design

MCP1640EV-SBC(2): Boost 3.3V or 5V, 0.35~5.5Vin

Manufacturer: Microchip Technology

* Output current is dependent on input voltage. The MCP1640 is a compact, high-efficiency, fixed frequency, synchronous step-up dc-dc converter. It provides an easy-to-use power supply solution for applications powered by one-cell, two-cell, or three-cell alkaline, NiCd, NiMH, one-cell Li-Ion or Li-Polymer batteries in addition to distributed 3.3V to 5.0V applications.

View Design

TPS5410EVM-203(2): 5V @ 1A, 7 ~ 36 Vin

Manufacturer: Texas Instruments

The TPS5410 dc/dc converter is designed to provide up to a 1-A output from an input voltage source of 5.5 V to 36 V. The TPS5410EVM-203 is designed using 2 independent circuits providing output voltages of 12 V and 5 V. Rated input voltage and output current range for the evaluation module is given in Table 1.

View Design

LMZ10503EXTEVAL: 2.5V @ 3A, 2.95 ~ 5.5V in

Manufacturer: Texas Instruments

The LMZ10503EXT SIMPLE SWITCHER® power module operates from -55°C ~ 125°C and is a complete, easy-to-use DC-DC solution capable of driving up to 3A load. It has exceptional power conversion efficiency, output voltage accuracy, line and load regulation.

View Design

RD-171 LM5001: +/- 5V @ 250mA, 10 ~ 30V in

Manufacturer: Texas Instruments

A very low noise differential power supply for split rail systems requiring low noise +5V and -5V (higher or lower voltage is possible). This design is fully isolated and capable of floating to over 500V differential from Vin to Vout (higher is possible).

View Design

UCC28600EVM: 120W, 19.4V @6.2A with PFC, 85~265VAC

Manufacturer: Texas Instruments

The UCC28600 evaluation module (EVM) is a 120-W off-line quasi-resonant flyback converter providing a 19.4-V regulated output at 6.2 A of load current, operating from a universal ac input.

View Design

STEVAL-ISA018V1: 150W, 24V @ 6A, 85~185/185~265VAC

Manufacturer: STMicroelectronics

This user manual describes a high efficiency solution for industrial power supplies with a continuous output power of 150 W and peak power up to 240 W. It takes advantage of the resonant approach to minimize switching losses, resulting in higher than 90% efficiency. The topology is based on half-bridge and operated in a resonant fashion by means of a resonant LC tank, driven by the L6599 dedicate…

View Design
793 Results - Page 1/80 |< < 1 2 3 4 5 > >|